If your shower has a leak, you might not even know it. However, that problem is about to become more apparent than ever with the increasing water bills hitting everyone’s utility bills these days. Sudden increases in water consumption can often be attributed to leaks. If you have a leaky faucet or shower mixer valve in your bathroom, you can effectively solve this problem by repairing it instead of replacing it. Here’s how you do it.
Check the Shower’s Water Flow
First, you want to make sure that your shower’s flow rate is sufficient. If your water flow is low, you might experience leaks or worse, your pipes could burst. If your shower has an improper flow rate, you can easily solve this problem by increasing the flow rate of the shower’s water pipe. The easiest way to do this is by removing the shower head. This will allow you to clean your shower head’s spout and the inside of the pipe. If the inside of the pipe is dirty, then it will reduce the amount of water that will flow through the pipe. Once you’ve increased the flow rate, you should test it by turning on the shower and checking the water’s temperature. If the temperature is too hot, then turn the water off immediately. Too low, then you can adjust the temperature as needed.
Be Alert for a Leak
In this situation, you want to be careful. You want to make sure that you’re not experiencing a leak that could occur due to a burst pipe. However, if you’re simply experiencing a leak that results from a damaged shower’s pipe, you can fix it easily using the instructions given below. First, you want to inspect the pipe for any damage. Look for any cracks in the pipe and make sure that there’s no excessive wear and tear on the shower. Next, you want to turn off the water to your home and use a wrench to loosen the shower’s pipe’s handle. Then, you want to twist the pipe while holding it with a wrench. This will allow you to break off any obstructions inside the pipe.
Fix a Shower Faucet or Mixer Valve
If your shower’s faucet is leaking, then you can easily fix it by simply replacing the faucet’s o-rings. This is a relatively easy task that doesn’t require a lot of skill. To do it, you can simply turn off your home’s water pipes and shut the valves for your water pipes. Then, you can simply flip off the shower’s handle and remove the shower head. After that, you can remove the old faucet and faucet’s o-rings and clean the area where the new faucet will be installed. Next, you can install the new faucet and o-rings. After that, you can turn the water and shower back on and test it to make sure there are no leaks.
Repair a Shower Head
If your shower head is damaged, you can easily repair it by simply replacing it. This is again a very easy task that doesn’t require a lot of skill. You can repair the damage by simply replacing the damaged part that is included in the new shower head. To do it, you can simply remove the old head and the diverter valve. After that, you can flip off the water supply to your home and turn on the water’s diverter valve. This will provide water to your new shower head. Next, you can install your new head and flip off the water. After that, you can turn on the water again and test it to make sure there are no leaks. If there are any leaks, then you can simply tighten the diverter valve.
Stop a Shower Mixer Valve from Leaking
If your shower’s mixer valve is leaking, you can easily fix it by replacing it. This is again a relatively easy task that doesn’t require a lot of skill. All you need to do is to flip off your shower’s valve handle and remove the shower head. After that, you can remove the valve and clean the area where the new valve will be installed. After that, you can flip on the new valve and clean the area again. Next, you can flip on the shower’s valve handle and check for leaks.
Conclusion
You can easily fix your shower’s leaky faucet or valve by simply replacing the faucet or valve. In addition, you can increase the flow rate of your shower’s water pipe by cleaning the pipe’s inside. However, if the problem persists, then you can always call for a professional plumber to help solve the problem. So, these are some of the ways how you can fix a leaking shower. With proper knowledge, you can easily repair or replace the parts that are leaking in your home. You can also stop a leaking shower mixer valve, repair a damaged shower head, and replace a leaking mixer valve. So, these are some of the ways how you can fix a leaking shower. With proper knowledge, you can easily repair or replace the parts that are leaking in your home. You can also stop a leaking shower mixer valve, repair a damaged shower head, and replace a leaking mixer valve.
